MikroTik Certified User Management Engineer

- PPP Profile + LAB;
- Local and Remote addresses;
- Incoming/Outgoing Filters;
- Address List;
- Change TCP-MSS;
- Use Encryption;
- Session Timeout;
- Rate-Limit configuration;
- Only-one setting;
- PPP Secret + LAB;
- Service and Profile;
- Local and Remote address;
- Routes configuration;
- Limit Bytes In/Limit Bytes Out configuration;
- IP Pool;
- Set addresses ranges;
- Next Pool options;

- PPTP and L2TP;
- Theory;
- Comparison;
- PPTP Client configuration + LAB;
- Client Setup;
- Set profile;
- Dial-on-Demand;
- Add Default Route and static routes;
- PPTP Server configuration + LAB;
- Enable server;
- Setup profiles;
- Add clients to /ppp secret;
- Set static interfaces for clients;
- L2TP Client configuration + LAB;
- Client setup;
- Configure profile;
- Dial-on-Demand;
- Add Default Route and static routes;
- PPTP Server configuration + LAB;
- Enable server;
- Set profiles;
- Add clients to /ppp secret;
- Set Static interfaces for clients;

- PPPoE server and client;
- Theory;
- Usage environment;
- Comparison to othe PPP protocols;
- PPPoE client configuration + LAB;
- Client setup;
- Select interface;
- Service name
- Configure profile;
- PPPoE Server configuration + LAB;
- Enable PPPoE server;
- Set profiles;
- Add clients to /ppp secret;
- Add Static interfaces for clients;
- Secure server by removing any IP address from PPPoE server interface;
- Encryption + LAB;
- Set profile without encryption;
- Set profile with encryption;
- Configure PPPoE client without encryption;
- Interface ECMP;
- set ECMP routes for ppp interfaces;

- L2TP and EoIP + LAB;
- Set L2TP tunnel;
- Set EoIP tunnel;
- Create bridge and add necessary interfaces to ports;
- Confirm you have Ethernet connectivity between remote nodes;
- L2TP and VPLS + LAB;
- Set L2TP tunnel;
- Set VPLS tunnel;
- Create bridge and add necessary interfaces to ports;
- L2TP and BCP + LAB;
- Set L2TP tunnel;
- Use BCP to bridge PPP interface;
- Add to bridge necessary interface;
- Multilink Protocol;
- Enable Multilink by specifying correct MRRU settings;
- Disable Mangle rules for MSS adjustment;
- MLPPP [optional];
- Setup client and specify multiple interfaces for one client;
- Set PPPPoE server with MLPPP support;

- Introduction;
- Theory and concepts;
- Comparison to other VPN protocols;
- IPSec Peer;
- Use different authentication methods;
- IPSec exchange modes;
- Encryption and Hash algorithms;
- NAT-Traversal;
- Lifetime and Lifebytes;
- DPD protocol;
- Policy;
- IPsec protocol and action;
- Tunnels;
- Generate dynamic Policy;
- Proposal;
- Encryption and Authentication algorithms;
- Lifetime;
- PFS;
- Installed-SA;
- Flush SA;
- Create IPSec between two routers with NAT + LAB;
- Set peer;
- Set policy;
- Set NAT rules;
- Confirm the secure link is established;

- Introduction;
- Concepts;
- Usage environments;
- Setup HotSpot with default settings + LAB;
- HotSpot Login Methods + LAB;
- HTTP CHAP/PAP;
- MAC;
- Cookie;
- HTTPS;
- Trial;
- RADIUS
- Users + LAB;
- Add users;
- Set MAC-address for user
- Set MAC-address for username;
- Limit Uptime and Limit Bytes In/Out;
- Reset limits for user;
- Monitor Users;
- Host Table;
- Active Table;
- SNMP for users;
- Profile + LAB;
- Keepalive timeout;
- Shared users;
- Rate-Limit;
- Address-list;
- Incoming/Outgoing filter;
- Incoming/Outgoing Packet Mark;
- Bypass HotSpot;
- walled-garden;
- walled-garden ip;
- ip-binding;
- Customize HotSpot + LAB;
- Advertisement;
- Customize pages;

- RADIUS client + LAB
- add radius client;
- set service;
- use-radius for the specific service
- RADIUS server;
- User Manager + LAB
- Install the latest user-manager;
- Add routers;
- Add users;
- Set profile;
- RADIUS incoming